Moxa Technologies NPort 5200 Serie User Manual Page 138
- Page / 259
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CN2610 User’s Manual Setting Up Multi-Host TTY
10-5
Setting Value Notes Necessity
Max. Sessions 1-8 Select the maximum number of
simultaneous sessions that will be
allowed for this serial port.
Optional
Terminal mode no. Star NT-560+,
NL-5000A,
VT100
CN2610 provides 3 modes that
depend on the connection mode
supported by the terminal.
Optional
Inactivity time 0-99 minutes Idle time before the port is
disconnected automatically. If set to
0 minutes, the port will not
disconnect.
Optional
TCP alive check
time
0-99 minutes The time period CN2610 waits
before checking if the TCP
connection is alive or not. If no
response is received, CN2610 will
reset the port and terminate the
connection.
Optional
Session
Hot Key
TCP port
Remote IP
Configure the Hot key, TCP port,
and Remote IP address for each
session.
3. Press Esc to return to the PORT MENU.
Configuring the Serial Ports
Open Port Menu Æ Line to configure serial port settings.
1. From the MAIN MENU, select Port, and then press Enter.
CN2610-8 CN2610-8_19 V2.0 MAIN MENU
------------------------------------------------------------------------------
Server [Port] seTting sAve Utility Restart Exit
Examine/modify async server ports configuration
Enter: select ESC: previous menu
2. From the PORT MENU, select Line, and then press Enter.
CN2610-8 CN2610-8_19 V2.0 PORT MENU
------------------------------------------------------------------------------
Mode [Line] mOdem Welcome_MSG Quit
Examine/modify asynchronous port configuration
Enter: select ESC: previous menu
3. The Line page has pop-up selection lists for Port, Speed, Bits, Stop, Parity, FIFO,
RTS/CTS, XON/XOFF, and Discon. ctrl for each serial port. Each item is described in detail
below the figure.
- CN2610 Dual-LAN Async Server 1
- User’s Manual 1
- Copyright Notice 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- Introduction 8
- Product Features 9
- Package Checklist 9
- Front Panel 10
- Rear Panel 10
- Bottom Label 10
- Getting Started 11
- Hardware Installation 12
- Wiring Requirements 13
- Connecting to the Network 13
- Configuration Checklist 14
- Using Telnet 16
- 2. Click Next to Continue 17
- 5. Click Next to continue 18
- 7. Click Close 19
- Server Configuration—Info 22
- Server Configuration—LAN 24
- Server Configuration—Adv 25
- Knowing Your Application 31
- 12345678 32
- Serial ports 32
- 9 10111213141516 32
- Finger Printer 35
- Ethernet 35
- UDP datagram 35
- Terminal Access (Terminal) 39
- Real TTY/Unix Fixed TTY 44
- Configuring ASPP Mode 47
- Installing Ports 58
- Installing a Server 66
- Next to continue 67
- Setting 79
- Setting Up Device Control 90
- Configuring RAW Mode 95
- ASPP Library Introduction 99
- ASPP Examples for Unix 99
- ASPP Examples for Windows 100
- Setting Up Raw UDP 101
- Selecting the Application 103
- Configuring RAW UDP Mode 104
- Configuring the Serial Ports 105
- Restart 107
- Data Acquisition System 108
- Async Server CN2610-8 109
- DRDAS Mode 111
- Setting Up Reverse Terminal 116
- Configuring RTELNET Mode 119
- Setting Up Terminal 123
- Configuring TERM_ASC Mode 126
- Configuring TERM_BIN Mode 128
- Setting Up Multi-host TTY 134
- Configuring FIXTTY Mode 137
- Setting up Hosts 140
- Configuring tty Redirection 141
- Terminal Access 141
- Using Fixed TTY Driver 142
- Setting Up Dialin/out 143
- Configuring PPPD/PPP Mode 146
- Configuring SLIPD/SLIP Mode 148
- Configuring Dynamic Mode 150
- Optional Welcome Message 157
- Setting Up Printer 160
- Configuring RAW PRN Mode 163
- Configuring LPD PRN Mode 165
- Setting up Unix Hosts 168
- Setting up a LINUX Host 170
- Setting up Windows Hosts 171
- Setting Up Multiplex 180
- Code Reader 182
- Equipment 182
- Setting Up Routing 193
- What is RIP? 195
- Configuring RIP 195
- 196
- Static Routing Examples 197
- 16 port RS-232 Async Server 198
- Administrative Utilities 201
- Monitor 202
- Network 204
- Routing 206
- PPP-Trace 206
- Diagnostic 207
- Upgrade 208
- Console Terminal Upgrade 209
- Remote RCP Upgrade 214
- Console Terminal Export 216
- Remote RCP Export 219
- Console Terminal Import 219
- Default 222
- Press any key to cancel 223
- Appendix A Troubleshooting 224
- Console Terminal Problems 225
- Terminal Port Problems 227
- Saving CN2610’s Parameters 228
- ASPP Port Problems 228
- SLIP/PPP Connection Problems 228
- RADIUS Problems 229
- Appendix B RADIUS Server 230
- What is RADIUS? 231
- Setting up CN2610 231
- Dialin/out—Dynamic Mode 232
- Dialin/out—PPP/PPPD Mode 233
- Setting up UNIX Hosts 234
- RADIUS Server Configuration 235
- Add/Modify permission group 236
- Basic Permission Maintenance 237
- User Settings 238
- RADIUS proxy 239
- Setting up Windows NT Hosts 240
- 6. Specify an IP address 243
- Supported SNMP variables 247
- Pin Assignments 250
- Cable Wiring 250
- Appendix E LCM Display 253
- Problem Report Form 256
- Product Return Procedure 256
- MOXA Internet Services 256
- MOXA Internet Services 257
- Problem Report Form 258
- MOXA CN2610 Series 258
- Product Return Procedure 259
Related products and manuals for Servers Moxa Technologies NPort 5200 Serie
Servers Moxa Technologies 331 User Manual
(69 pages)
(69 pages)
Servers Moxa Technologies 2140 User Manual
(102 pages)
(102 pages)
Servers Moxa Technologies 331 User Manual
(13 pages)
(13 pages)
Servers Moxa Technologies DE-304 User Manual
(14 pages)
(14 pages)
Servers Moxa Technologies 304 Specifications
(20 pages)
(20 pages)
(91 pages)© 2020, manymanuals.com. All rights reserved. | 0.914 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals