Moxa Technologies NPort 5200 Serie User Manual Page 189
- Page / 259
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CN2610 User’s Manual Setting Up Multiplexor
13-10
Setting Value Notes Necessity
Quit Key ^E Defines the Quit key used to disconnect
the link between the current terminal
session and the remote host. It may be
left blank for binary communication.
Optional
Auto-link protocol None/Telnet/
Rlogin
None: Do not connect to the host
automatically.
Telnet: Connects to the host
automatically by Telnet.
Rlogin: Connects to the host
automatically by Rlogin.
Optional
Telnet TCP port 23 Enter a number or leave the space blank.
If not specified, then by default, port 23
is used. If you want to use Telnet without
a TCP port number, set this option to 23.
Optional
Primary host IP IP address or
the name
defined in the
[Host] table
If specified, designates a ‘permanent’
host to which the terminal will always be
connected.
Optional
Link by input IP Enable/
Disable
For users to enter the connection IP
address manually.
Optional
Secondary host IP IP address or
the name
defined in the
[Host] table.
If specified, designates a secondary
‘permanent’ host to which the terminal
will be connected.
Optional
Auto-login prompt ogin: Send ID information when this prompt is
received.
Optional
Password prompt assword: Send Password information when this
prompt is received
Optional
Login user name Login ID Optional
Login password Login Password Optional
Terminal type ansi Terminal type for outgoing connection Optional
Inactivity time 0-99 minutes Idle time before the port is disconnected
automatically. If set to 0 minutes, the
port will not disconnect.
Optional
Authentication
type
None/local/
server
None: Authentication is not required.
local: Check the ID stored in the
User_table (defined under the SERVER
MENU).
Server: Check the ID with the
external RADIUS server. Refer to
Appendix C for RADIUS installation
information.
Optional
TCP alive check
time
0-99 minutes The time period CN2610 waits before
checking if the TCP connection is alive
or not. If no response is received,
CN2610 will reset the port and terminate
the connection.
Optional
- CN2610 Dual-LAN Async Server 1
- User’s Manual 1
- Copyright Notice 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- Introduction 8
- Product Features 9
- Package Checklist 9
- Front Panel 10
- Rear Panel 10
- Bottom Label 10
- Getting Started 11
- Hardware Installation 12
- Wiring Requirements 13
- Connecting to the Network 13
- Configuration Checklist 14
- Using Telnet 16
- 2. Click Next to Continue 17
- 5. Click Next to continue 18
- 7. Click Close 19
- Server Configuration—Info 22
- Server Configuration—LAN 24
- Server Configuration—Adv 25
- Knowing Your Application 31
- 12345678 32
- Serial ports 32
- 9 10111213141516 32
- Finger Printer 35
- Ethernet 35
- UDP datagram 35
- Terminal Access (Terminal) 39
- Real TTY/Unix Fixed TTY 44
- Configuring ASPP Mode 47
- Installing Ports 58
- Installing a Server 66
- Next to continue 67
- Setting 79
- Setting Up Device Control 90
- Configuring RAW Mode 95
- ASPP Library Introduction 99
- ASPP Examples for Unix 99
- ASPP Examples for Windows 100
- Setting Up Raw UDP 101
- Selecting the Application 103
- Configuring RAW UDP Mode 104
- Configuring the Serial Ports 105
- Restart 107
- Data Acquisition System 108
- Async Server CN2610-8 109
- DRDAS Mode 111
- Setting Up Reverse Terminal 116
- Configuring RTELNET Mode 119
- Setting Up Terminal 123
- Configuring TERM_ASC Mode 126
- Configuring TERM_BIN Mode 128
- Setting Up Multi-host TTY 134
- Configuring FIXTTY Mode 137
- Setting up Hosts 140
- Configuring tty Redirection 141
- Terminal Access 141
- Using Fixed TTY Driver 142
- Setting Up Dialin/out 143
- Configuring PPPD/PPP Mode 146
- Configuring SLIPD/SLIP Mode 148
- Configuring Dynamic Mode 150
- Optional Welcome Message 157
- Setting Up Printer 160
- Configuring RAW PRN Mode 163
- Configuring LPD PRN Mode 165
- Setting up Unix Hosts 168
- Setting up a LINUX Host 170
- Setting up Windows Hosts 171
- Setting Up Multiplex 180
- Code Reader 182
- Equipment 182
- Setting Up Routing 193
- What is RIP? 195
- Configuring RIP 195
- 196
- Static Routing Examples 197
- 16 port RS-232 Async Server 198
- Administrative Utilities 201
- Monitor 202
- Network 204
- Routing 206
- PPP-Trace 206
- Diagnostic 207
- Upgrade 208
- Console Terminal Upgrade 209
- Remote RCP Upgrade 214
- Console Terminal Export 216
- Remote RCP Export 219
- Console Terminal Import 219
- Default 222
- Press any key to cancel 223
- Appendix A Troubleshooting 224
- Console Terminal Problems 225
- Terminal Port Problems 227
- Saving CN2610’s Parameters 228
- ASPP Port Problems 228
- SLIP/PPP Connection Problems 228
- RADIUS Problems 229
- Appendix B RADIUS Server 230
- What is RADIUS? 231
- Setting up CN2610 231
- Dialin/out—Dynamic Mode 232
- Dialin/out—PPP/PPPD Mode 233
- Setting up UNIX Hosts 234
- RADIUS Server Configuration 235
- Add/Modify permission group 236
- Basic Permission Maintenance 237
- User Settings 238
- RADIUS proxy 239
- Setting up Windows NT Hosts 240
- 6. Specify an IP address 243
- Supported SNMP variables 247
- Pin Assignments 250
- Cable Wiring 250
- Appendix E LCM Display 253
- Problem Report Form 256
- Product Return Procedure 256
- MOXA Internet Services 256
- MOXA Internet Services 257
- Problem Report Form 258
- MOXA CN2610 Series 258
- Product Return Procedure 259
Related products and manuals for Servers Moxa Technologies NPort 5200 Serie
Servers Moxa Technologies 331 User Manual
(69 pages)
(69 pages)
Servers Moxa Technologies 2140 User Manual
(102 pages)
(102 pages)
Servers Moxa Technologies 331 User Manual
(13 pages)
(13 pages)
Servers Moxa Technologies DE-304 User Manual
(14 pages)
(14 pages)
Servers Moxa Technologies 304 Specifications
(20 pages)
(20 pages)
(91 pages)© 2020, manymanuals.com. All rights reserved. | 1.506 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals