Moxa Technologies NPort 5200 Serie User Manual Page 225
- Page / 259
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CN2610 User’s Manual Troubleshooting
A-2
Console Terminal Problems
Problem: No message is displayed on the console terminal.
Solutions:
¾ Check to see if the terminal is set to 115200 bps, 8 data bits, no parity, 1 stop bit.
¾ Check to see if the RS-232 cable is wired correctly. The console needs CTS/DCD signals
to trigger. Refer to the “Cable Wiring” section in Appendix D.
¾ The console may be blocked waiting for an event. Press ESC to try unblocking.
Problem: Garbage characters are displayed on the console terminal.
Solutions:
¾ Check to see if the terminal is set to 115200 bps, 8 data bits, no parity, 1 stop bit.
¾ Check to see if terminal type setting is correct. The console only accepts ansi/vt100 or
vt52.
¾ Press Ctrl-L to refresh the display.
Question: How can I restore CN2610 to the factory default settings?
Solution:
¾ After entering the Console window, select setting Æ Default, and then press Enter. The
CN2610 will be restored to the factory default settings.
CN2610-8 CN2610-8_19 V2.0 MAIN MENU
---------------------------------------------------------------------------
Server Port [seTting] sAve Utility Restart Exit
Export or import configuration
Enter: select ESC: previous menu
CN2610-8 CN2610-8_19 V2.0
---------------------------------------------------------------------------
Export Import [Default] Quit
Load the factory setting
ESC: back to menu Enter: select
+--------------------------------------------------+
|Enter to load factory setting, other key to cancel|
+--------------------------------------------------+
Question: If I forget the password for my CN2610, what should I do?
Solution:
¾ Press the “Password Reset button” on the CN2610’s front panel for more than 5 seconds.
The password stored in the Flash ROM will be erased. Refer to Chapter 1 for more details.
- CN2610 Dual-LAN Async Server 1
- User’s Manual 1
- Copyright Notice 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- Introduction 8
- Product Features 9
- Package Checklist 9
- Front Panel 10
- Rear Panel 10
- Bottom Label 10
- Getting Started 11
- Hardware Installation 12
- Wiring Requirements 13
- Connecting to the Network 13
- Configuration Checklist 14
- Using Telnet 16
- 2. Click Next to Continue 17
- 5. Click Next to continue 18
- 7. Click Close 19
- Server Configuration—Info 22
- Server Configuration—LAN 24
- Server Configuration—Adv 25
- Knowing Your Application 31
- 12345678 32
- Serial ports 32
- 9 10111213141516 32
- Finger Printer 35
- Ethernet 35
- UDP datagram 35
- Terminal Access (Terminal) 39
- Real TTY/Unix Fixed TTY 44
- Configuring ASPP Mode 47
- Installing Ports 58
- Installing a Server 66
- Next to continue 67
- Setting 79
- Setting Up Device Control 90
- Configuring RAW Mode 95
- ASPP Library Introduction 99
- ASPP Examples for Unix 99
- ASPP Examples for Windows 100
- Setting Up Raw UDP 101
- Selecting the Application 103
- Configuring RAW UDP Mode 104
- Configuring the Serial Ports 105
- Restart 107
- Data Acquisition System 108
- Async Server CN2610-8 109
- DRDAS Mode 111
- Setting Up Reverse Terminal 116
- Configuring RTELNET Mode 119
- Setting Up Terminal 123
- Configuring TERM_ASC Mode 126
- Configuring TERM_BIN Mode 128
- Setting Up Multi-host TTY 134
- Configuring FIXTTY Mode 137
- Setting up Hosts 140
- Configuring tty Redirection 141
- Terminal Access 141
- Using Fixed TTY Driver 142
- Setting Up Dialin/out 143
- Configuring PPPD/PPP Mode 146
- Configuring SLIPD/SLIP Mode 148
- Configuring Dynamic Mode 150
- Optional Welcome Message 157
- Setting Up Printer 160
- Configuring RAW PRN Mode 163
- Configuring LPD PRN Mode 165
- Setting up Unix Hosts 168
- Setting up a LINUX Host 170
- Setting up Windows Hosts 171
- Setting Up Multiplex 180
- Code Reader 182
- Equipment 182
- Setting Up Routing 193
- What is RIP? 195
- Configuring RIP 195
- 196
- Static Routing Examples 197
- 16 port RS-232 Async Server 198
- Administrative Utilities 201
- Monitor 202
- Network 204
- Routing 206
- PPP-Trace 206
- Diagnostic 207
- Upgrade 208
- Console Terminal Upgrade 209
- Remote RCP Upgrade 214
- Console Terminal Export 216
- Remote RCP Export 219
- Console Terminal Import 219
- Default 222
- Press any key to cancel 223
- Appendix A Troubleshooting 224
- Console Terminal Problems 225
- Terminal Port Problems 227
- Saving CN2610’s Parameters 228
- ASPP Port Problems 228
- SLIP/PPP Connection Problems 228
- RADIUS Problems 229
- Appendix B RADIUS Server 230
- What is RADIUS? 231
- Setting up CN2610 231
- Dialin/out—Dynamic Mode 232
- Dialin/out—PPP/PPPD Mode 233
- Setting up UNIX Hosts 234
- RADIUS Server Configuration 235
- Add/Modify permission group 236
- Basic Permission Maintenance 237
- User Settings 238
- RADIUS proxy 239
- Setting up Windows NT Hosts 240
- 6. Specify an IP address 243
- Supported SNMP variables 247
- Pin Assignments 250
- Cable Wiring 250
- Appendix E LCM Display 253
- Problem Report Form 256
- Product Return Procedure 256
- MOXA Internet Services 256
- MOXA Internet Services 257
- Problem Report Form 258
- MOXA CN2610 Series 258
- Product Return Procedure 259
Related products and manuals for Servers Moxa Technologies NPort 5200 Serie
Servers Moxa Technologies 331 User Manual
(69 pages)
(69 pages)
Servers Moxa Technologies 2140 User Manual
(102 pages)
(102 pages)
Servers Moxa Technologies 331 User Manual
(13 pages)
(13 pages)
Servers Moxa Technologies DE-304 User Manual
(14 pages)
(14 pages)
Servers Moxa Technologies 304 Specifications
(20 pages)
(20 pages)
(91 pages)© 2020, manymanuals.com. All rights reserved. | 0.152 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals